How to Clean an Amiga Case – Amiga 1200 Case Restoration

07 April 2020 · Updated 26 October 2026 5 min read Mark Baxman

A grubby Amiga 1200 case can make a perfectly good machine look tired. Decades of dust, nicotine, sticky fingers and old stickers build up in the textured plastic, and a quick wipe rarely shifts it. The good news is that a proper clean, done safely, can transform the look of the machine without risking the plastic or the badges.

This guide covers a full clean of the A1200 case halves, from stripping the machine down to drying and reassembly. If your case is yellowed rather than dirty, cleaning is still the essential first step before any retrobright treatment.

Before you start

Never wash the case with the electronics inside. You need to remove the motherboard, keyboard, floppy drive and any hard drive first. Our Amiga 1200 disassembly guide shows each step, including how to release the fragile keyboard ribbon cable safely.

Keep the screws together, and photograph the case before cleaning so you know where any labels and the LED lens sit.

What you need

Step 1: Remove loose dust

Brush or vacuum out the vents and corners before you wet anything. Dust turns into a paste when wet and is harder to remove afterwards.

Step 2: Protect the badges and labels

The A1200 has a printed or applied logo on the top case and labels on the underside. Water and scrubbing can lift or fade them. Cover them with masking tape, or clean around them with a damp cloth rather than a brush. Do not soak the underside label.

Step 3: Wash the case halves

Fill a bowl or sink with warm, not hot, water and a few drops of washing-up liquid. Wash each half, working the brush gently in small circles over the textured surfaces. Hot water can warp plastic, and harsh scrubbing can polish the texture into shiny patches.

Rinse with clean water to remove soap residue.

Step 4: Deal with stubborn marks

  • Scuffs and grime in the texture: a slightly damp melamine sponge can lift them, but it is mildly abrasive, so use light pressure and test on a hidden area first.
  • Sticker residue: soften with isopropyl alcohol on a cloth, then wipe away. Avoid acetone and strong solvents, which attack ABS plastic and can leave permanent marks.
  • Pen and marker: isopropyl alcohol often helps; test first.

Step 5: Clean the keycaps separately

If the keyboard needs attention too, remove the keycaps and wash them separately in warm soapy water, then dry them completely. Never wash the keyboard membrane or ribbon. Our A1200 keyboard repair guide covers this in detail, and where to find new keycaps if any are missing or broken.

Step 6: Dry thoroughly

Shake off excess water, pat the case dry with a microfibre cloth, and leave it to air dry for several hours, ideally overnight. Water hides in screw posts and seams. Do not use a heat gun or a hot oven, which can warp the plastic.

Step 7: Inspect before reassembly

Once the case is clean, check it in good light:

  • Is it evenly coloured, or yellowed? Yellowing does not wash off.
  • Are there cracks around the screw posts, the rear ports or the trapdoor?
  • Are any feet missing?

What about yellowing?

Amiga plastics yellow with age because of the flame retardants in the plastic. Cleaning will not remove it. The usual treatment is “retrobrighting” with hydrogen peroxide and UV light, which can restore the original colour. It needs care, as it can leave streaks and the yellowing may return over time. See our guide to restoring a yellowed Amiga case with peroxide.

Reassembly tips

Make sure everything is completely dry before refitting the electronics. Reconnect the keyboard ribbon squarely and lock its clip, refit the LED cable, and do not overtighten the screws into the plastic posts. While the machine is apart, it is also a good moment to look at a recap: see our Amiga 1200 refurbishment guide.

Products to avoid

ProductWhy
Acetone and nail polish removerDissolves and marks ABS plastic
BleachCan discolour plastic and damage labels
Abrasive cream cleanersScratch and polish the texture
Very hot water or dishwashersRisk of warping

FAQ

Can I put my Amiga case in a dishwasher?

It is not recommended. The heat can warp the plastic and the detergent can damage labels. Wash it by hand in warm soapy water.

How do I remove sticker residue from an Amiga case?

Soften it with isopropyl alcohol on a cloth, then wipe it away. Avoid acetone, which damages ABS plastic.

Will cleaning remove yellowing from an Amiga case?

No. Yellowing is a chemical change in the plastic. It needs a retrobright treatment, such as hydrogen peroxide with UV light.

Is a magic eraser safe on Amiga plastic?

Used gently and tested first, it can lift grime from the texture. It is mildly abrasive, so heavy use can leave shiny patches.