A desoldering pump, often called a solder sucker, is one of the cheapest and most useful tools on a repair bench. But every time you use it, a little blob of molten solder shoots into the barrel and hardens. After a while those bits build up, the plunger stops sealing, and the pump loses its suction or jams completely.
Cleaning one takes about five minutes and usually brings it back to full strength. This guide covers the common spring-loaded type with a plastic or PTFE nozzle, which is what most people own.
Signs your pump needs cleaning
- The suction is weak, and solder is left in the hole after a stroke.
- The plunger does not lock down, or it sticks part way.
- You can hear loose solder rattling around inside.
- Solder dribbles out of the nozzle when you push the plunger down.
If you have been using the pump on a big job, such as desoldering through-hole components across a whole board, empty it as you go rather than waiting for it to clog.
What you need
- A small cross-head screwdriver, if your pump has screws.
- A cotton bud or small brush, and a cloth.
- A small amount of silicone grease for the seal, if it looks dry.
- Optionally, a replacement nozzle if yours is burnt or deformed.
Wear safety glasses when you take the pump apart. The spring is under tension, and loose bits of solder can fly out.
Step 1: Empty the loose solder
Many pumps simply unscrew in the middle or at the nozzle end. Unscrew the nozzle or barrel section and tip the loose solder out over a bin. You may find dozens of small balls and flakes. Do not blow into the pump to clear it.
Step 2: Take out the plunger
On most pumps, unscrewing the barrel releases the plunger assembly and spring. Pull it out carefully, noting the order of the parts, and keep the spring with it. Take a photo before you remove anything if you are not sure how it goes back.
Step 3: Clean the barrel and plunger
Wipe the inside of the barrel with a cloth or cotton bud to remove solder residue and flux. A little isopropyl alcohol helps dissolve sticky flux; let it dry fully afterwards. Clean the plunger and its rubber seal or O-ring the same way, and check for flakes of solder stuck to the seal, which stop it sealing properly.
Inspect the seal. If it is cracked, torn or flattened, it will never seal well, and you need a replacement seal or a new pump.
Step 4: Clean or replace the nozzle
The tip takes most of the heat and gets clogged with solder. Push a thin piece of wire through it to clear the hole, being careful not to enlarge or crack it. If the nozzle is badly melted, burnt or out of round, replace it; a damaged tip will never seal against the joint.
Step 5: Lubricate the seal
A very thin smear of silicone grease on the plunger seal helps it slide smoothly and seal well. Use only a small amount, as too much attracts dust and solder flakes. Avoid oils that can attack rubber.
Step 6: Reassemble and test
Put the plunger and spring back in the barrel in the same order, screw the parts together, and test it: push the plunger down until it locks, cover the nozzle with your finger and press the release button. You should feel a strong suction pulling at your finger.
Using it so it stays clean
- Use enough heat: melt the joint completely, then put the nozzle right over the joint and trigger the pump.
- Add a little fresh solder to old, dry joints first. Old solder flows badly, and new leaded solder lowers the melting point.
- Empty the pump regularly by pushing the plunger down over a bin.
- Keep the nozzle tip clear of the iron itself; touching the hot iron melts and deforms it.
- Use solder wick for the last traces of solder, or for surface-mount pads where a pump is not suitable.
Is it worth upgrading?
Cheap pumps work, but a good-quality metal-bodied desoldering pump with a replaceable tip usually has stronger suction and lasts much longer. For large restoration jobs, a desoldering station with a heated nozzle and vacuum pump is faster again.
For other methods, see our guides to removing solder without a pump, using solder wick and removing stubborn solder from holes.
FAQ
Why has my desoldering pump lost suction?
Usually because solder debris has built up inside, the plunger seal is dirty or worn, or the nozzle is clogged or damaged. Cleaning and inspecting the seal fixes most pumps.
Can I lubricate a desoldering pump?
Yes. A very thin smear of silicone grease on the plunger seal helps it slide and seal. Use very little.
How often should I empty a solder sucker?
Empty it whenever you hear solder rattling inside, and during any large job. Regular emptying stops debris jamming the plunger.
Can I replace a desoldering pump nozzle?
On most pumps, yes. Replacement nozzles are cheap, and a melted or deformed nozzle should be replaced because it will not seal against the joint.